46 type 595d solid tantalum chip capacitors t antamount ? , conformal terminals, maximum c/v features features features features features ? new extended range offerings. ? new lower esr reading. ? largest capacitance rating in the industry. ? compatible with 293d molded chip mounting pad layout. ? terminations: 60/40 tin lead (2) standard (electroplate or solder dip). ? 8mm, 12mm tape available per eia-481-1 and reeling per iec 286-3. 7" [178mm] standard. 13" [330mm] available. ? operating temperature: - 55 c to + 125 c. ? case code compatibility with eia 535baac and cecc 30801 molded chips. case code t a b c d r dimensional configurations dimensional configurations dimensional configurations dimensional configurations dimensional configurations [numbers in brackets indicate millimeters] performance characteristics performance characteristics performance characteristics performance characteristics performance characteristics operating temperature: - 55 c to + 85 c. (to + 125 c with voltage derating.) capacitance tolerance: at 120 hz, + 25 c. 20% standard. 10% available. dissipation factor: at 120 hz, + 25 c. dissipation factor, as determined from the expression 2 p frc, shall not exceed the values listed in the standard ratings tables. dc leakage current (dcl max.): at + 25 c: leakage current shall not exceed the values listed in the standard ratings tables. at + 85 c: leakage current shall not exceed 10 times the values listed in the standard ratings tables. at + 125 c: leakage current shall not exceed 12 times the values listed in the standard ratings tables. life test: capacitors shall withstand rated dc voltage applied at + 85 c for 2000 hours or derated dc voltage applied at + 125 c for 1000 hours. following the life test: 1. dcl shall meet the original requirement. 2. dissipation factor and esr shall meet the original requirement. 3. change in capacitance shall not exceed 10%. electrical characteristics @ + 25 electrical characteristics @ + 25 electrical characteristics @ + 25 electrical characteristics @ + 25 electrical characteristics @ + 25 c c c c c dcl: .01 m a/cv or .5 m a whichever is greater. df: 4% 1 m f, 6% > 1 m f < 100 m f, 8% 3 100 m f < 560 m f, 10% 560 m f & 680 m f, 16% 1000 m f, 20% 1500 m f. j w tantalum wire nib identifies anode (+) terminal j h a l b d l (max.) .087 [2.2] .146 [3.7] .158 [4.0] .281 [7.1] .293 [7.5] .283 [7.2] w .045 .010 [1.1 0.3] .072 .010 [1.8 0.3] .110 + .010 - .016 [2.8 + 0.3 - 0.4] .126 .010 [3.2 0.3] .170 .010 [4.3 0.3] .235 .010 [6.0 0.3] h .045 .010 [1.1 0.3] .056 .012 [1.4 0.3] .075 + .012 - .025 [1.9 + 0.3 - 0.6] .098 .012 [2.5 0.3] .110 .012 [2.8 0.3] .136 .012 [3.5 0.3] a .016 .008 [.4 0.2] .031 .012 [.80 .30] .031 .012 [.80 .30] .051 .017 [1.3 .30] .051 .017 [1.3 .30] .051 .017 [1.3 .30] b .042 .010 [1.07 0.25] .085 .015 [2.2 0.4] .097 .015 [2.5 0.4] .180 .025 [4.6 0.6] .180 .025 [4.6 0.6] .180 .025 [4.6 0.6] d (ref.) .063 [1.6] .115 [2.9] .138 [3.5] .236 [6.0] .253 [6.4] .243 [6.2] j (max.) .004 [0.1] .004 [0.1] .004 [0.1] .004 [0.1] .004 [0.1] .004 [0.1] note: the anode termination (d less b) will be a minimum of .010" [0.3mm]. t case = .005" [.13mm] minimum. vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon
47 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 120 150 180 220 270 330 390 470 560 680 1000 1500 m f type 595d type 595d type 595d type 595d type 595d std. std. std. std. std. std. std. std. rated voltage vr @ + 85 c ratings and case codes ratings and case codes ratings and case codes ratings and case codes ratings and case codes * contact factory for availability. ** part numbers shown for units with 20% capacitance tolerance. for 10% units, change "x0" to "x9". * extended ratings shown in bold print. 4.7 10.0 15.0 33.0 33.0 100.0 120.0 150.0 180.0 220.0 270.0 270.0 390.0 470.0 680.0* 680.0 1000.0 1500.0* 4 wvdc @ + 85 c, surge = 5.2 v . . . 2.7 wvdc @ + 125 c, surge = 3.4 v capacitance ( m f) max. ripple 100khz irms (amps) max. esr @ + 25 c 100khz (ohms) max. df @ + 25 c 120 hz (%) max. dcl @ + 25 c ( m a) part number** standard ratings standard ratings standard ratings standard ratings standard ratings case code 0.5 0.5 0.6 1.3 1.3 4.0 4.8 6.0 7.2 8.8 10.8 10.8 15.6 18.8 27.2 27.2 40.0 60.0 6 6 6 6 6 8 8 8 8 8 8 8 8 8 10 10 16 20 7.8 7.8 1.4 1.4 0.47 0.45 0.19 0.18 0.14 0.14 0.17 0.13 0.13 0.13 0.13 0.11 0.07 0.07 0.06 0.06 0.22 0.22 0.41 0.42 0.76 0.78 1.04 1.04 0.80 1.07 1.07 1.39 1.07 1.51 1.88 1.88 595d475x0004t2t 595d106x0004t2t 595d156x0004a2t 595d336x0004a2t 595d336x0004b2t 595d107x0004b2t 595d127x0004c2t 595d157x0004c2t 595d187x0004d2t 595d227x0004d2t 595d277x0004c2t 595d277x0004d2t 595d397x0004d2t 595d477x0004r2t 595d687x0004d2t* 595d687x0004r2t 595d108x0004r2t 595d158x0004r2t* t t a a b b c c d d c d d r d* r r r* 4 v ext. 6.3 v ext. 10 v ext. 16 v ext. 20 v ext. 25 v ext. 35 v ext. 50 v ext. 3.3 6.8 15.0 22.0 22.0 33.0 t t a a b a 0.5 0.5 0.9 1.4 1.4 2.1 6 6 6 6 6 6 8.5 8.5 1.7 1.7 0.57 1.70 595d335x06r3t2t 595d685x06r3t2t 595d156x06r3a2t 595d226x06r3a2t 595d226x06r3b2t 595d336x06r3a2t 0.06 0.06 0.20 0.20 0.37 0.20 vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon * contact factory for availability. note: this table shows the largest capacitance values available in the case size and voltage indicated. 6.3 wvdc @ + 85 c, surge = 8 v . . . 4 wvdc @ + 125 c, surge = 5 v t a b c d r t a b c d d* r r* t a b c d r t a b c d d* r t a b c d r t a b c d d* r r* r* t a b c d r t a b b* c d r t a b c d r a b c d r t a b c d r a b c d r t a b c d r a b c d r t a b c d r a b c d r
48 type 595d type 595d type 595d type 595d type 595d * contact factory for availability. ** part numbers shown for units with 20% capacitance tolerance. for 10% units, change "x0" to "x9". * extended ratings shown in bold print. capacitance ( m f) max. ripple 100khz irms (amps) max. esr @ + 25 c 100khz (ohms) max. df @ + 25 c 120 hz (%) max. dcl @ + 25 c ( m a) part number** standard ratings standard ratings standard ratings standard ratings standard ratings case code 2.2 4.7 10.0 15.0 15.0 47.0 68.0 120.0 150.0 150.0 180.0 220.0 220.0 270.0 330.0* 330.0 390.0 470.0* 680.0* 68.0 100.0 120.0 180.0 220.0 220.0 330.0 330.0 390.0 470.0* 560.0 680.0 1000.0 6.3 wvdc @ + 85 c, surge = 8 v . . . 4 wvdc @ + 125 c, surge = 5 v b c c d c d d r r d* r r r 4.3 6.3 7.6 11.3 13.9 13.9 20.8 20.8 24.6 29.6 35.3 42.8 63.0 6 8 8 8 8 8 8 8 8 8 10 10 16 0.55 0.20 0.19 0.14 0.18 0.14 0.14 0.13 0.13 0.13 0.11 0.09 0.07 0.38 0.74 0.76 1.04 0.78 1.04 1.04 1.39 1.39 1.07 1.51 1.66 1.88 595d686x06r3b2t 595d107x06r3c2t 595d127x06r3c2t 595d187x06r3d2t 595d227x06r3c2t 595d227x06r3d2t 595d337x06r3d2t 595d337x06r3r2t 595d397x06r3r2t 595d477x06r3d2t* 595d567x06r3r2t 595d687x06r3r2t 595d108x06r3r2t 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 8 8 8 10 8.6 8.6 1.9 1.8 0.67 0.65 0.24 0.14 0.22 0.14 0.13 0.14 0.13 0.13 0.14 0.13 0.12 0.12 0.09 0.06 0.06 0.19 0.20 0.35 0.35 0.68 1.04 0.71 1.04 1.39 1.04 1.39 1.39 1.04 1.39 1.44 1.44 1.66 0.5 0.5 1.0 1.5 1.5 4.7 6.8 12.0 15.0 15.0 18.0 22.0 22.0 27.0 33.0 33.0 39.0 47.0 68.0 t t a a b b c d c d r d r r d* r r r* r* 595d225x0010t2t 595d475x0010t2t 595d106x0010a2t 595d156x0010a2t 595d156x0010b2t 595d476x0010b2t 595d686x0010c2t 595d127x0010d2t 595d157x0010c2t 595d157x0010d2t 595d187x0010r2t 595d227x0010d2t 595d227x0010r2t 595d277x0010r2t 595d337x0010d2t* 595d337x0010r2t 595d397x0010r2t 595d477x0010r2t* 595d687x0010r2t* 1.5 3.3 4.7 6.8 10.0 10.0 15.0 15.0 33.0 33.0 47.0* 47.0 68.0 100.0 100.0 120.0 150.0 150.0 180.0 220.0 t t a a a b a b b c b* c d c d r d r r r 595d155x0016t2t 595d335x0016t2t 595d475x0016a2t 595d685x0016a2t 595d106x0016a2t 595d106x0016b2t 595d156x0016a2t 595d156x0016b2t 595d336x0016b2t 595d336x0016c2t 595d476x0016b2t* 595d476x0016c2t 595d686x0016d2t 595d107x0016c2t 595d107x0016d2t 595d127x0016r2t 595d157x0016d2t 595d157x0016r2t 595d187x0016r2t 595d227x0016r2t 0.5 0.5 0.8 1.1 1.6 1.6 2.4 2.4 5.3 5.3 7.5 7.5 10.9 16.0 16.0 19.2 24.0 24.0 28.8 35.2 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8.7 8.6 2.9 2.8 2.5 0.76 2.40 0.75 0.72 0.29 0.72 0.28 0.14 0.27 0.14 0.14 0.14 0.13 0.13 0.12 0.06 0.06 0.16 0.16 0.17 0.32 0.17 0.33 0.33 0.62 0.33 0.63 1.04 0.64 1.04 1.34 1.04 1.39 1.39 1.44 0.68 1.0 2.2 3.3 4.7 4.7 6.8 6.8 10.0 t t a a a b a b b 595d684x0020t2t 595d105x0020t2t 595d225x0020a2t 595d335x0020a2t 595d475x0020a2t 595d475x0020b2t 595d685x0020a2t 595d685x0020b2t 595d106x0020b2t 0.5 0.5 0.5 0.7 0.9 0.9 1.4 1.4 2.0 0.05 0.06 0.14 0.14 0.15 0.29 0.15 0.29 0.28 10.8 9.0 3.8 3.8 3.1 0.95 3.0 0.95 1.0 4 4 6 6 6 6 6 6 6 vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon 20 wvdc @ + 85 c, surge = 26 v . . . 13 wvdc @ + 125 c, surge = 16 v 16 wvdc @ + 85 c, surge = 20 v . . . 10 wvdc @ + 125 c, surge = 12 v 10 wvdc @ + 85 c, surge = 13 v . . . 7 wvdc @ + 125 c, surge = 8 v
49 type 595d type 595d type 595d type 595d type 595d standard ratings standard ratings standard ratings standard ratings standard ratings capacitance ( m f) case code part number** max. dcl @ + 25 c ( m a) max. ripple 100khz irms (amps) max. esr @ + 25 c 100khz (ohms) max. df @ + 25 c 120hz (%) 0.47 1.5 2.2 3.3 6.8 10.0 10.0 15.0 22.0 22.0 33.0 47.0 47.0 68.0 100.0 t a a b b b c c c d d d r r r 595d474x0025t2t 595d155x0025a2t 595d225x0025a2t 595d335x0025b2t 595d685x0025b2t 595d106x0025b2t 595d106x0025c2t 595d156x0025c2t 595d226x0025c2t 595d226x0025d2t 595d336x0025d2t 595d476x0025d2t 595d476x0025r2t 595d686x0025r2t 595d107x0025r2t 0.5 0.5 0.6 0.8 1.7 2.5 2.5 3.8 5.5 5.5 8.3 11.8 11.8 17.0 25.0 4 6 6 6 6 6 6 6 6 6 6 6 6 6 8 13.5 3.8 3.8 1.9 1.5 1.5 0.57 0.56 0.50 0.28 0.27 0.26 0.20 0.20 0.20 0.05 0.14 0.14 0.21 0.23 0.23 0.44 0.44 0.47 0.73 0.75 0.76 1.12 1.12 1.12 ** part numbers shown for units with 20% capacitance tolerance. for 10% units, change "x0" to "x9". ** extended ratings shown in bold print. 0.10 0.15 0.22 0.33 0.47 0.68 0.68 1.0 1.5 2.2 2.2 3.3 4.7 6.8 6.8 10.0 10.0 15.0 22.0 50 wvdc @ + 85 c, surge = 65 v . . . 33 wvdc @ + 125 c, surge = 38 v 0.33 0.47 0.68 1.0 1.5 1.5 2.2 3.3 4.7 4.7 6.8 10.0 15.0 15.0 22.0 22.0 33.0 47.0 35 wvdc @ + 85 c, surge = 46 v . . . 23 wvdc @ + 125 c, surge = 26 v 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 22.5 18.0 15.3 8.1 7.2 6.1 5.4 5.0 1.8 3.2 1.7 1.6 1.4 1.3 0.82 0.80 0.65 0.40 0.39 0.04 0.04 0.04 0.09 0.10 0.11 0.12 0.13 0.25 0.16 0.25 0.26 0.28 0.29 0.43 0.43 0.62 0.79 0.80 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.8 1.1 1.1 1.7 2.4 3.4 3.4 5.0 5.0 7.5 11.0 t t t a a a b b c b c c c c d d r r r 595d104x0050t2t 595d154x0050t2t 595d224x0050t2t 595d334x0050a2t 595d474x0050a2t 595d684x0050a2t 595d684x0050b2t 595d105x0050b2t 595d155x0050c2t 595d225x0050b2t 595d225x0050c2t 595d335x0050c2t 595d475x0050c2t 595d685x0050c2t 595d685x0050d2t 595d106x0050d2t 595d106x0050r2t 595d156x0050r2t 595d226x0050r2t 0.05 0.13 0.13 0.13 0.14 0.17 0.19 0.38 0.19 0.41 0.42 0.59 0.43 0.60 0.68 0.94 0.94 0.94 14.4 4.3 4.2 4.1 3.8 2.8 2.3 0.75 2.2 0.66 0.63 0.43 0.60 0.41 0.32 0.28 0.28 0.28 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 0.5 0.5 0.5 0.5 0.5 0.5 0.8 1.2 1.6 1.6 2.4 3.5 5.3 5.3 7.7 7.7 11.6 16.5 595d334x0035t2t 595d474x0035a2t 595d684x0035a2t 595d105x0035a2t 595d155x0035a2t 595d155x0035b2t 595d225x0035b2t 595d335x0035c2t 595d475x0035b2t 595d475x0035c2t 595d685x0035c2t 595d106x0035d2t 595d156x0035c2t 595d156x0035d2t 595d226x0035d2t 595d226x0035r2t 595d336x0035r2t 595d476x0035r2t t a a a a b b c b c c d c d d r r r 20 wvdc @ + 85 c, surge = 26 v . . . 13 wvdc @ + 125 c, surge = 16 v 15.0 22.0 47.0 47.0 100.0 100.0 120.0 150.0 b c c d d r r r 595d156x0020b2t 595d226x0020c2t 595d476x0020c2t 595d476x0020d2t 595d107x0020d2t 595d107x0020r2t 595d127x0020r2t 595d157x0020r2t 3.0 4.4 9.4 9.4 20.0 20.0 24.0 30.0 0.28 0.54 0.56 0.89 0.91 1.34 1.34 1.34 1.0 0.38 0.35 0.19 0.18 0.14 0.14 0.14 6 6 6 6 8 8 8 8 25 wvdc @ + 85 c, surge = 32 v . . . 17 wvdc @ + 125 c, surge = 20 v vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon
50 type 595d type 595d type 595d type 595d type 595d typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency "a" case "t" case 1000 100 10 1.0 0.1 ohms impedance esr 1 m f, 35 vdc 15 m f, 6.3 vdc frequency in hertz 10000 1000 100 10 1.0 impedance esr 0.1 m f, 50 vdc 3.3 m f, 6.3 vdc ohms frequency in hertz "c" case "b" case ohms 1000 100 10 1.0 0.1 impedance esr 10 m f, 25 vdc ohms 1000 100 10 1.0 0.1 impedance esr 2.2 m f, 35 vdc 22 m f, 6.3 vdc frequency in hertz frequency in hertz "r" case "d" case frequency in hertz ohms 100 10 1.0 0.1 0.0 impedance esr 33 m f, 35 vdc 390 m f, 6.3 vdc frequency in hertz 100 10 1.0 0.1 0.0 impedance esr 220 m f, 6.3 vdc ohms 22 m f, 25 vdc 100 m f, 6.3 vdc how to order how to order how to order how to order how to order blank = bulk pack t = tape and reel 7" [178mm] reel w = 13" [330mm] reel see tape and reel specifications. t packaging 2 = 60/40 tin lead. standard. 2 termination see ratings and case codes table. a case code 010 dc voltage rating @ + 85 c this is expressed in volts. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an "r" (6r3 = 6.3 volts). x0 capacitance tolerance this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. 106 capacitance x0 = 20% x9 = 10% 595d type 100 1k 10k 100k 1m 10m 100 1k 10k 100k 1m 10m 100 1k 10k 100k 1m 10m vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon 100 1k 10k 100k 1m 10m 100 1k 10k 100k 1m 10m 100 1k 10k 100k 1m 10m note: parts qualified and identified to tighter capacitance tolerance and/or higher rated voltage, are substitutable for parts ordered to looser capacitance tolerance and/or lower rated voltage, provided other values, such as case size and termination remain the same.
51 type 595d type 595d type 595d type 595d type 595d tape and reel packaging tape and reel packaging tape and reel packaging tape and reel packaging tape and reel packaging [numbers in brackets indicate millimeters] note: metric dimensions will govern. dimensions in inches are rounded and for reference only. user direction of feed .030 [0.75] min. (note 3) center lines of cavity .079 .002 [2.0 0.05] p 1 .030 [0.75] min. (note 4) deformation between embossments .059 + .004 - 0.0 [1.5 + 0.10 - 0.0] .069 .004 [1.75 0.10] .157 .004 [4.0 0.10] embossment w f b 0 a 0 top cover tape 10 pitches cumulative tolerance on tape 0.008 [0.2] maximum cavity size (note 1) b 1 max. (note 6) for tape feeder reference only including draft. concentric around b 0 (note 5) top cover tape .004 [0.10] max. .024 [0.600] max. k 0 d 1 min. for components .079 x .047 [2.0 x 1.2] and larger. (note 5) (side or front sectional view) maximum component rotation 20 t 2 max. top cover tape thickness embossment carrier standard orientation is with the cathode (-) nearest to the sprocket holes per eia-481-1 and iec 286-3. notes: 1. a 0 b 0 k 0 are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. the clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (a 0 b 0 k 0 ) must be within .002" [0.05mm] minimum and .020" [0.50mm] maximum. the clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees. 2. tape with components shall pass around radius "r" without damage. the minimum trailer length may require additional length t o provide r minimum for 12mm embossed tape for reels with hub diameters approaching n minimum. 3. this dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape betw een the embossed cavities or to the edge of the cavity whichever is less. 4. this dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformati on of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. the embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. dimensions of embossment location and hole location shall be applied independent of each other. 6. b 1 dimension is a reference dimension for tape feeder clearance only. a 0 b 0 k 0 tape size 8mm 12mm 12mm double pitch b 1 (max.) (note 6) .179 [4.55] .323 [8.2] .323 [8.2] d 1 (min.) (note 5) .039 [1.0] .059 [1.5] .059 [1.5] f .138 .002 [3.5 0.05] .217 .002 [5.5 0.05] .217 .002 [5.5 0.05] p 1 .157 .004 [4.0 0.1] .157 .004 [4.0 0.1] .315 .004 [8.0 0.1] r (min.) (note 2) .984 [25.0] 1.181 [30.0] 1.181 [30.0] t 2 (max.) .098 [2.5] .256 [6.5] .256 [6.5] w .315 + .012 - .004 [8.0 + 0.3 - 0.1] .472 .012 [12.0 .30] .472 .012 [12.0 .30] (note 1) tape and reel specifications: all case codes are available on plastic embossed tape per eia-481-1. tape reeling per iec 286-3 is also available. standard reel diameter is 7" [178mm]. 13" [330mm] reels are available and recommended as the most cost effective packaging method. the most efficient packaging quantities are full reel increments on a given reel diameter. the quantities shown allow for the sealed empty pockets required to be in conformance with eia-481-1. reel size and packaging orientation must be specified in the vishay sprague part number. .039 [1.0] max. 3.937 [100.0] tape camber (top view) allowable camber to be .039/3.937 [1/100] non-cumulative over 9.843 [250.0] 9.843 [250.0] 20 maximum component rotation (top view) typical component center line typical component cavity center line b 0 a 0 .039 [1.0] max. 10,000 9000 8000 3000 2500 units per reel 13" [330] reel 7" [178] reel component pitch tape width case code t a b c d r 2500 2000 2000 500 500 600 4mm 4mm 4mm 8mm 8mm 8mm 8mm 8mm 12mm 12mm 12mm 12mm bending radius (note 2) r min. vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon
52 type 595d where, p = power dissipation in watts @ + 25 c as given in the table in paragraph number 5 (power dissipation). r esr = the capacitor equivalent series resistance at the specified frequency. 2. a-c ripple voltage: the maximum allowable ripple voltage shall be determined from the formula: or, from the formula: v rms = i rms x z where, p = power dissipation in watts @ + 25 c as given in the table in paragraph number 5 (power dissipation). r esr = the capacitor equivalent series resistance at the specified frequency. z = the capacitor impedance at the specified frequency. 2.1 the sum of the peak ac voltage plus the dc voltage shall not exceed the dc voltage rating of the capacitor. 2.2 the sum of the negative peak ac voltage plus the applied dc voltage shall not allow a voltage reversal exceeding 10% of the dc working voltage at + 25 c. 3. reverse voltage: these capacitors are capable of withstanding peak voltages in the reverse direction equal to 10% of the dc rating at + 25 c and 5% of the dc rating at + 85 c. 4. temperature derating: if these capacitors are to be operated at temperatures above + 25 c, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: guide to application guide to application guide to application guide to application guide to application 1. a-c ripple current: the maximum allowable ripple current shall be determined from the formula: p r esr i rms = z v rms = p r esr t a b c d r maximum permissible power dissipation @ + 25 c (watts) in free air case code 6. recommended mounting pad geometries: the nib must have sufficient clearance to avoid electrical contact with other components. the width dimension indicated is the same as the maximum width of the capacitor. this is to minimize lateral movement. derating factor 1.0 0.9 0.8 0.4 temperature + 25 c + 55 c + 85 c + 125 c 5. power dissipation: power dissipation will be affected by the heat sinking capability of the mounting surface. non-sinusoidal ripple current may produce heating effects which differ from those shown. it is important that the equivalent irms value be established when calculating permissible operating levels. (power dissipation calculated using + 25 c temperature rise.) [numbers in brackets indicate millimeters] * pads for b, c and d case codes are otherwise pad compatible with * type 293d, b, c and d case codes respectively. reflow solder pads* reflow solder pads* reflow solder pads* reflow solder pads* reflow solder pads* width (a) .055 [1.5] .082 [2.1] .120 [3.0] .136 [3.5] .180 [4.6] .245 [6.3] pad metallization (b) .030 [0.7] .065 [1.7] .065 [1.7] .090 [2.3] .090 [2.3] .090 [2.3] separation (c) .025 [0.6] .050 [1.3] .065 [1.7] .120 [3.1] .145 [3.7] .145 [3.7] case code t a b c d r a b b c 0.030 0.070 0.080 0.110 0.150 0.250 vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon
|
